Educational explanation

What is a structural calculation?

A structural calculation shows whether a structure is safe under load; it is required for wall openings, extensions and permits. Sterkteberekeningen in Utrecht delivers it to the Eurocodes with a fixed quote. Below is an educational explanation of the principles; it is not intended as an official calculation.

For an official calculation for your permit: structural engineer Utrecht or structural calculation costs.

1

The basics & shear stress

You can get to grips with strength of materials by calculating a beam cantilevering out of a wall at A. To prevent the beam from failing under load, we check the shear and bending stresses caused by the load (see below) in the most heavily loaded section at A, where the bending moment is greatest.

architecture The moment

This moment equals the force(s) multiplied by the distance perpendicular to the direction of the force.

M = F * a
  • M = bending moment at the fixed support
  • F = force (in newtons)
  • a = minimum distance from the line of action of the force to the fixed support at A

A fixed support is a connection that can take horizontal and vertical reactions and a bending moment at the wall without rotating. If a 2 m long cantilever is loaded at its end by a force P = 2.0 kN downwards, then by equilibrium the vertical reaction VAP at A is 2.0 kN → upwards.

The self-weight (line load q in kN/m) of a beam with a chosen depth h = 225 mm and a chosen width b = 70 mm is:

q = 0.225 m * 0.07 m * 5 kN/m³ (unit weight)
q = 0.08 kN/m

From the equilibrium of q it follows that:

VAq = ql = 0.08 * 2 = 0.16 kN

The total vertical reaction at A is then:

VA = VAP + VAq = 2.16 kN

The vertical reaction VA causes a vertical shear stress in section A of:

τA = VA / bh
τA = 2,160 N / (225 mm * 70 mm)
τA = 0.14 N/mm²

Check against the permissible limit:

0.14 N/mm² < 0.8 N/mm²

Limit = 2.0 (shear strength C18) * 0.7 (climate/duration) / {1.35 (load) * 1.3 (material)}

check_circle

Because the shear stress is lower than the adjusted shear strength, the shear stress in this structure is acceptable.

2

Bending moment & bending stress

The bending moment in the most heavily loaded section A due to P is:

MAP = 2.0 kN * 2 m = 4.0 kNm

The moment due to self-weight gives:

MAq = ql (force due to q) * 1/2 (distance to centroid)
MAq = ql² / 2 = 0.08 * 2² / 2 = 0.16 kNm

Total moment:

MA = MAP + MAq = 4.16 kNm

The section modulus W3) determines the stresses σ in a section due to a bending moment M according to: σ = M/W

If the beam has the same rectangular section along its whole length, it is prismatic and:

W = bh² / 6 = 70 * 225² / 6 = 590,625 mm³

At the bottom and top edges of the beam there is then a horizontal bending stress of:

σA = 4.16 kNm / 590,625 mm³ = 7.0 N/mm²

Check against the permissible limit:

7.0 N/mm² < 7.2 N/mm²

Limit = 18 (bending strength C18) * 0.7 (climate/duration) / {1.3 (material) * 1.35 (load)}

check_circle

Because the bending stress is lower than the adjusted bending strength, the bending stress in this structure is acceptable.

3

Deflection

We also check the deflection of the beam. For a cantilever, the immediate elastic deformation uBP;elastic at B is:

uBP;elastic = Pl³ / {3 E1) I2)}
= 2000 N * 2000³ mm³ / { 3 * 9000 N/mm² * (1/12) * 70 mm * 225³ mm³ } = 8.9 mm

For a cantilever, q causes the immediate elastic deformation:

uBq;elastic = ql⁴ / { 8 EI }
= 0.08 N/mm * 2000⁴ mm⁴ / { 8 * 9000 N/mm² * (1/12) * 70 mm * 225³ mm³ } = 0.3 mm

Total immediate elastic deflection:

uB;elastic = 8.9 + 0.3 = 9.2 mm

Time-dependent deflection (creep)

The total deflection equals the immediate elastic deflection plus the time-dependent deflection (creep).

uB;creep = (elastic deformation due to permanent load) +
0.6 (creep factor) * 0.4 (if the variable load is present 40% of the time) *
(elastic deformation due to variable load)

uB;creep = 0.3 + (0.6 * 0.4 * 8.9) = 2.4 mm

Totals:

uB;total = 9.2 + 2.4 = 11.6 mm
uB;inst = uBq;elastic = 0.3 mm (instantaneous, due to permanent load)
uB;add = uB;total - uB;inst = 11.3 mm (additional deflection)

Requirement A) Additional deflection

11.3 mm < 12 mm

Limit: 0.006 * 2000 mm = 12 mm (requirement for a cantilever)

Requirement B) Total deflection

11.6 mm < 16 mm

Limit: 0.008 * 2000 mm = 16 mm

check_circle

Because the deformations that occur are smaller than the maximum permissible deformation, the deformations of this structure are acceptable.

Note: because uB;total = 11.6 mm is already below the stricter limit of 12 mm (requirement A), requirement A is met at the same time. The additional deflection did not actually need to be calculated.

Conclusion

The strength of the material is used well, so the structure is designed to be economical and safe.

Explanation of variables

  • 1)
    E = modulus of elasticity = stress / [strain = elongation per length]
    For timber grade C18, E = 9,000 N/mm²
  • 2)
    I = moment of inertia = { ∫∫ z² dy dz where z = distance to the centre of the beam, integration limits for z: h/2 and -h/2 and for y: the side edges }
    I = bh³ / 12 for a rectangular section, because then ∫dy = b
  • 3)
    W = I / (h/2). For a rectangular section this gives:
    W = (bh³ / 12) / (h/2) = bh² / 6.